Incinerator manufacturer

Incineration is the most obvious solution for total destruction of municipal waste, avoiding 

all the direct and indirect risks associated with other disposal methods.

Incineration perfectly fits into a trend of treating waste in a safe way, and if possible, at the same 

place where it was generated to avoid cross-contamination risk and to keep waste treatment costs at acceptable level.

WWW.HICLOVER.COMWaste Incinerators Auto Roll Air Filters
Nanjing Clover Medical Technology Co.,Ltd.

Tel:  +86-25-8461 0201   

Mobile: +86-13813931455(whatsapp/wechat)
Email: [email protected]
Email: [email protected]  
Items/Model TS10(PLC) TS20(PLC) TS30(PLC) TS50(PLC) TS100(PLC)
Burn Rate (Average) 10 kg/hour 20 kg/hour 30 kg/hour 50 kg/hour 100 kg/hour
Feed Capacity(Average) 20kg 40kg 60kg 100kg 200 kg
Combustion Chamber 100L 210L 330L 560L 1200L
Internal Dimensions 50x50x40cm 65x65x50cm 75x75x60cm 100x80x70cm 120x100x100cm
Secondary Chamber 50L 110L 180L 280L 600L
Smoke Filter Chamber Yes Yes Yes Yes Yes
Feed Mode Manual Manual Manual Manual Manual
Voltage 220V 220V 220V 220V 220V
Power 0.5Kw 0.5Kw 0.5Kw 0.7Kw 0.7Kw
Oil Consumption (kg/hour) 5.4–12.6 7.8–16.3 10.2–20 12.1–24 14–28
Gas Consumption (m3/hour) 6.2–11.4 8–15.7 9.8–20 9.9–26.1 10–32.2
Temperature Monitor Yes Yes Yes Yes Yes
Temperature Protection Yes Yes Yes Yes Yes
Oil Tank 100L 100L 100L 100L 200L
Feed Door 30x30cm 45x40cm 55x50cm 70x55cm 80x60cm
Chimney 3Meter 3Meter 5Meter 5Meter 10Meter
Chimney Type Stainless Steel Stainless Steel Stainless Steel Stainless Steel Stainless Steel
1st. Chamber Temperature 800–1000 800–1000 800–1000 800–1000 800–1000
2nd. Chamber Temperature 1000-1200 1000-1200 1000-1200 1000-1200 1000-1200
Residency Time 2.0 Sec. 2.0 Sec. 2.0 Sec. 2.0 Sec. 2.0 Sec.
Gross Weight 1500kg 2200kg 3000kg 4500kg 6000kg
External Dimensions 140x90x120cm 160x110x130cm 175x120x140cm 230x130x155cm 260x150x180cm

Secondary Combustion Chamber (After burner)
Heavy-duty steel casing
High quality refractory lining and insulation
1 x oil burner
Should be fitted with burners that use low sulphur fuel.
Ensure secondary air supply is controlled.
Ensure residence time is not less than two seconds.
Ensure that the gas temperature as measured against the inside wall in the secondary chamber 

and not in the flame zone is not less than 1100 degrees centigrade.
Ensure the emitted oxygen content of the emitted gases is not less than 11%
Ensure both primary and secondary combustion temperatures are maintained until all waste is completely combusted.
The chimney should have a minimum height of 10 meters above ground level and clear the 
highest point of the building by not less than 3 meters for all roofs. The topography and height of adjacent 
buildings within 50 meters radius should be taken into account.
The chimney should be visible to the operator from the feeding area
Low running and maintenance costs
Fully Automatic and simple to operate control panel
Afterburner Preheat
Incineration Temperatures in Excess of 900 degrees C
3 mm Steel Casing and Fully insulated
Dense Refractory Concrete Lining Rated to 1400 degrees C
Solid Hearth to Allow Maximum Burnout
Large Top Opening Lid For Easy Loading
Stainless Steel Flue as standard
12 Months or 1000 hours Warranty.
Optional Stainless Steel Casing
Heat Recovery System option